Lmst

I am now listening to Landscape by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/Landscape

I am now listening to Nitro by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/Nitro

I am now listening to Fog by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/Fog

I am now listening to AR by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/AR

I am now listening to Reconstruct by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/Reconstruct

I am now listening to Δ by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/%CE%94

I am now listening to Alchemy by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/Alchemy

Active variable Low Pass Filter (LPF) that offers you the ability to select a cut-off frequency anywhere inside the range 220Hz-16.5kHz through its single knob. The filter’s curve is quite steep offering a 12dB octave attenuation.

It’s the ideal device if you are looking to "clean-up” the harsh high end of your audio signal such as fret buzz, string noise, and higher harmonics or noise produced from other effects in your chain such as distortion pedals.
Alternatively you can use it to simulate the high frequency roll-off of speaker cabinets in case you’re experimenting with audio recording or your live setups.

Use it either with a guitar or a bass or even with synths and line level signals. If you need extra headroom you can always power the pedal with a voltage larger than the typical 9V.
With the max supply voltage being 24V the device can offer a max headroom of about 22Vpp.

--- Specifications ---
- Cut-off frequency range: 220Hz-16.5kHz (12dB/octave)
- Input impedance: 5Mohm
- Output impedance: 100ohm
- Voltage required: 9V (max 24V)
- Polarity: Center Negative
- Approximate headroom vs supply voltage: 7Vpp@9V || 10Vpp@12V || 22Vpp@24V
- Current consumption: 5mA
- Weight: ~125gr
- Enclosure dimensions: 93x38x32mm (3.66x1.49x1.26in)

#LPF #lowpassfilter #lowpass #guitarfilter #basspedals #guitarpedals #audiofilter #dpfx #dpFXpedals #boutiquepedals #handmadeeffects #handpaintedpedals #handmadepedals #pedalseffects #pedalsandeffects #variablefilter #variableLPF #filterpedal #filter #greekpedals #pedalbuilder #lpfpedal #lowpassfilterpedal #エフェクター

DIY guitar distortion effect pedal with ESP8266: construction, use and adjustment

https://www.techrm.com/diy-guitar-distortion-effect-pedal-with-esp8266-construction-use-and-adjustment/

#1N4148, #2N2222, #amplifier, #analogue, #analogueelectronics, #breadboard, #cutofffrequency, #digitalpotentiometer, #diode, #distorsion, #Dupontcables, #esp8266, #filter, #invertingamplifier, #LM386, #LM833, #lowpass, #MCP41010, #opamp, #operationalamplifier, #oscilloscope, #platformio, #potentiometer, #resistor, #speaker, #transistor

Sound engineering: build your own low pass op amp filter with adjustable cutoff frequency with digital potentiometer

https://www.techrm.com/sound-engineering-build-your-own-low-pass-op-amp-filter-with-adjustable-cutoff-frequency-with-digital-potentiometer/

#amplifier, #analogue, #analogueelectronics, #breadboard, #cutofffrequency, #digitalpotentiometer, #Dupontcables, #esp8266, #filter, #invertingamplifier, #LM386, #LM833, #lowpass, #MCP41010, #opamp, #operationalamplifier, #oscilloscope, #platformio, #potentiometer, #resistor, #speaker

Active variable LPF that offers you the ability to select a cut-off frequency anywhere inside the range 220Hz-16.5kHz through its single knob. The filter’s curve is quite steep offering a 12dB/octave attenuation.

It’s the ideal device if you are looking to "clean-up” the harsh high end of your audio signal such as fret buzz, string noise, and higher harmonics or noise produced from other effects in your chain such as distortion pedals.
Alternatively you can use it to simulate the high frequency roll-off of speaker cabinets in case you’re experimenting with audio recording or your live setups.

Use it either with a guitar or a bass or even with synths and line level signals. If you need extra headroom you can always power the pedal with a voltage larger than the typical 9V.
With the max supply voltage being 24V the device can offer a max headroom of about 22Vpp.

--- Specifications ---
- Cut-off frequency range: 220Hz-16.5kHz (12dB/octave)
- Input impedance: 5Mohm
- Output impedance: 100ohm
- Voltage required: 9V (max 24V)
- Polarity: Center Negative
- Approximate headroom vs supply voltage: 7Vpp@9V || 10Vpp@12V || 22Vpp@24V
- Current consumption: 5mA
- Weight: ~125gr
- Enclosure dimensions: 93x38x32mm (3.66x1.49x1.26in)

#LPF #lowpassfilter #lowpass #guitarfilter #basspedals #guitarpedals #audiofilter #dpfx #dpFXpedals #boutiquepedals #handmadeeffects #handpaintedpedals #handmadepedals #pedalseffects #pedalsandeffects #variablefilter #variableLPF #filterpedal #filter #greekpedals #pedalbuilder #lpfpedal #lowpassfilterpedal

I am now listening to AR by Low-pass #Lowpass
https://www.last.fm/music/Low-pass/_/AR

For the #weight data, all I really want is for it to be *smoothed* so I can see the longer-term trends. That's easy, with a #lowpass #filter.

I'm going to set my sights now on a different #dataset: #Electrical consumption gathered from my #power meter.

Don’t miss NL_CL2 FLESH this weekend! (24th May at 8pm NL time, online)
https://instrumentinventors.org/event/nl_cl-2-flesh/

I will participate with the performance 'Radio-active Monstrosities'.

This edition is curated by iii resident @joanachicau, hosted by iii member Marije Baalman, exploring the embodiment of live coding.

#voice #gender #radio #distorted #mediated #female #php #webaudio #javascript #monstrosity #echo #lowpass #lowpitch #livecoding #embodiment

#lowpass

Client Info