DomBus tracker controller working with Home Assistant, NodeRED, Domoticz, MQTT, Modbus, ... www.creasol.it/DBT
Performance comparison between fixed solar system on the roof and dual axis sun tracker
#homeassistant #nodered #modbusRTU #MQTT #domoticz #SunTracker #SolarTracker

#ChangeMyMind https://imgflip.com/i/8nqxrq
#EnergieWende #BalkonSolar #solarpunk #SolarTracker #Drehvorrichtung #SunTracker

Robot Sunflower Follows the Sun https://hackaday.com/2023/11/03/robot-sunflower-follows-the-sun/ #ArduinoHacks #SolarHacks #suntracker #sunflower #servo

No-Laser CNC Engraver is Something New Under the Sun

Hooking up a laser to a CNC gantry isn't exactly an Earth-shattering innovation, but it does make for a useful tool. Even a cheap diode laser mounted to an old 3D printer can do engraving, marking, or even light-duty cutting. But what about a laser engraver without the laser? Can that be of any use?

Apparently, the answer is yes, if you can harness the power of the sun. That's what [Lucas] did with his solar-tracking CNC engraver, the build of which is shown in the video below. The idea is pretty simple -- mount a decent-sized magnifying lens where the laser optics would normally go on a laser engraver, and point the thing at the sun. But as usual, the devil is in the details. The sun has a nasty habit of moving across the sky during the day, or at least appearing to, so [Lucas] has to add a couple of extra degrees of freedom to a regular X-Y CNC rig to track the sun. His tracking sensor is simplicity itself -- four CdS photocells arranged with a pair of perpendicular shades, and an Arduino to drive the gimbals in the correct direction to keep all four sensors equally illuminated. He had some initial problems getting the jerkiness out of the control loop, but the tracker eventually kept the whole thing pointing right at the Sun.

So how does it work? Not bad, actually -- [Lucas] managed to burn some pretty detailed designs into a piece of wood using just the sun. He mentions adding a shutter to douse the cutting beam to allow raster patterns, but even better might be a servo-controlled iris diaphragm to modulate beam intensity and control for varying sun conditions. He might also check out this solar engraver we covered previously for some more ideas, too.

Thanks to [Zane Atkins] for the tip.

#cnchacks #cds #cnc #engraver #gantry #gimbal #solar #suntracker

A Simple Sun Tracker With Very Few Parts

There are a huge number of ways to track the sun if you have some reason to do so. You can use time-based algorithms, or feed in coordinates from the Internet, or you could do it with minimal parts and no electronic processing at all. The latter is how this project from [3D Printer Academy] works.

One key thing about this project is that you shouldn't be fooled by the solar panels. They're not here to generate power for external use. Instead, they're wired up in opposing polarities to a DC gear motor. The motor turns the panel assembly. As one panel is hit by the sun, it turns the assembly to bring the other panel into the sun as well simply by applying a DC voltage to the motor. The other panel is wired up the opposite way, so if it is in the sun, it brings the other panel into alignment as well.

This serves as a very simple planar solar tracker. If you want to track the sun with minimal parts, this is a very easy way to do it. You'll just need to put whatever you want to actually aim at the sun on top of the assembly. if that happens to be a larger solar panel, it may be cumbersome and another more complex design may be more suitable.

It's an ingenious and easy way of tracking the sun, even if it's not immediately apparent how the device would be useful in its current form. If you've got an idea how you would use such a mechanism, let us know in the comments.

We've seen other solar tracker projects before, too. Video after the break.

#mischacks #solar #solarpanel #solartracker #suntracker